|
view |
Is there any port for an NXP Cortex evaluation board that support the .Net Micro Framework? Is NXP or any third party supporting the .NET Micro Framework? |
2012-11-21 15:56 |
|
view |
After a software reset like WD reset, BOD reset, is the SRAM content retained? |
2012-12-04 12:13 |
|
view |
An LPC1751 is programmed using CRP1, but Flash Magic (http://www.flashmagictool.com/) shows the CRP is disabled and can read the memory contents. |
2012-11-19 10:17 |
|
view |
Are there any DSP libraries available for the Cortex-M3 microcontrollers ? |
2012-11-27 00:30 |
|
view |
Are there Ethernet bootloaders available for LPC1700 and LPC2300/2400? If so, where can I find it? |
2012-11-19 10:07 |
|
view |
Can the RTC output be used for PLL0 input? |
2012-11-23 04:47 |
|
view |
Can the TC register and MRn register be written to while the timer is running? |
2012-11-23 04:46 |
|
view |
DMAReqSel on LPC17xx indicates UART0/MAT0.0, can both be used simultaneously to trigger a DMA request? |
2012-12-11 15:35 |
|
view |
Do the CAN controllers on LPC17xx have a Time Stamp function ? |
2012-11-27 00:25 |
|
view |
Do the CAN controllers on LPC17xx have a Time Stamp function ? |
2012-11-27 00:25 |
|
view |
Do the LPC17xx and LPC18xx have USB Flash loader like the LPC1343? |
2012-12-11 15:29 |
|
view |
Do the typical Brown-out Detection (BOD) voltages have any tolerance? |
2012-11-23 04:42 |
|
view |
Do you have a secondary USB bootloader for LPC17xx? |
2012-11-19 10:31 |
|
view |
Does CRP restrict IAP Flash entry points, i.e. can the application program the Flash even when CRP is enabled? |
2012-11-19 13:18 |
|
view |
Does the LPC17xx family of microcontrollers comply with IEC60335 safety standards? |
2012-11-19 09:49 |
|
view |
Has FatFS been ported to the LPC17xx ? |
2012-11-27 00:07 |
|
view |
How can I identify the Ethernet MAC ID to differentiate between 23xx/24xx/17xx? |
2012-12-11 15:30 |
|
view |
How can software detect that the external oscillator does not work, and it should use the internal RC oscillator instead, and report this as an error? |
2012-11-21 15:58 |
|
view |
How do I configure Lpcxpresso to place code in RAM? |
2012-11-21 16:07 |
|
view |
How long can short-circuit output current flow before damaging the microcontroller? |
2012-11-21 16:12 |
|
view |
How many breakpoints and watchpoints are supported on LPC17xx and other Cortex-M3 devices? |
2012-11-19 13:24 |
|
view |
How should the VBAT and RTCX1 pins on LPC17xx be configured when the RTC is not used? |
2012-11-19 13:22 |
|
view |
How to calculate the value of crystal load capacitors? |
2012-12-21 14:25 |
|
view |
I have an LPCXpresso LPC1768 board. Can I use OpenOCD to debug the target? |
2012-11-23 04:40 |
|
view |
I need BSDL files for 176x / 175x. Where can I find one? |
2012-11-27 00:23 |
English
简体中文
